CE 601 – Theory of Structures –II
Unit. I Moment
distribution method in analysis of frames with sway, analysis of box
frames, analysis of portals with inclined members, analysis of beams and
frames by Kani’s method.
Unit. II Plastic analysis of beams and frames.
Unit. III Analysis of tall frames, wind and earthquake loads,
codal provisions for lateral loads. Approximate analysis of multistory
frames for vertical and lateral loads.
Unit. IV Matrix method of structural analysis: force method and displacement method..
Unit. V Influence lines for intermediate structures, Muller Breslau principle, Analysis of Beam-Columns.
CE 602 – Water Resources and Irrigation Engineering
Unit-I
Hydrology : Hydrological cycle, precipitation and its measurement,
recording and non recording rain gauges, estimating missing rainfall
data, raingauge net works, mean depth of precipitation over a drainage
area, mass rainfall curves, intensity-duration curves, depth-area
duration curves, Infiltration and infiltration indices, evaporation
stream gauging, run off and its estimation, hydrograph analysis, unit
hydrograph and its derivation from isolated and complex storms, S- curve
hydrograph, synthetic unit hydrograph.
Unit-II Floods
and Ground water : Types of floods and their estimation by different
methods, probability and frequency analysis, flood routing through
reservoirs and channels, flood control measures, economics of flood
control, confined and unconfined aquifers, aquifer properties,
hydraulics of wells under steady flow conditions, infiltration
galleries. Ground water recharge- necessity and methods of improving
ground water storage. Water logging-causes, effects and its prevention.
Salt efflorescence-causes and effects. reclamation
of water logged and salt affected lands.
Unit-III Water
resources planning and management : Planning of water resources
projects, data requirements, economic analysis of water resources
projects appraisal of multipurpose projects, optimal operation of
projectsintrouduction to linear programming and its application to water
resources projects. Role of water in the environment, rain water
harvesting, impact assessment of water resources development and
managerial measures.
Unit - IV Irrigation
water requirement and soil-water-crop relationship: Irrigation,
definition, necessity, advantages and disadvantages, types and methods.
Irrigation development. Soils - types and their occurrence, suitability
for irrigation purposes, wilting coefficient and field capacity, optimum
water supply, consumptive use and its determination. Irrigation
methods- surface and subsurface, sprinkler and drip irrigation. Duty of
water, factors affecting duty and methods to improve duty, suitability
of water for irrigation, crops and crop seasons, principal crops and
their water requirement, crop ratio and crop rotation, intensity of
irrigation.
Unit - V Canal irrigation: Types of
canals, alignment, design of unlined and lined canals, Kennedy’s and
Lacey’s silt theories, typical canal sections, canal losses,
lininings-objectives, materials used, economics. Canal falls & cross
drainage works, - description and design, head and cross regulators.
escapes and outlets, canal transitions.
Well irrigation: Types of
wells, well construction, yield tests, specific capacity level and
specific yield, hydraulic design of open wells and tube wells, methods
of raising well water, characteristics of pumps and their selection,
interference of wells, well losses, advantages and disadvantages of well
irrigation.
CE 603 – Environmental Engg. - I
Unit - I Estimation
of ground and surface water resources. quality of water from different
sources, demand & quantity of water, fire demand, water requirement
for various uses, fluctuations in demand, forecast of population.
Unit - II
Impurities of water and their significance, water-borne diseases,
physical, chemical and bacteriological analysis of water, water
standards for different uses. Intake structure, conveyance of water,
pipe materials, pumps - operation & pumping stations.
Unit - III Water
Treatment methods-theory and design of sedimentation, coagulation,
filtration, disinfection, aeration & water softening, modern trends
in sedimentation & filtration, miscellaneous methods of treatment.
Unit - IV
Layout and hydraulics of different distribution systems, pipe fittings,
valves and appurtenances, analysis of distribution system. Hardy cross
method, leak detection, maintenance of distribution systems, service
reservoir capacity and height of reservoir.
Unit - V
Rural water supply schemes, financing and management of water supply
project, water pollution control act, conservancy & water carriage
system, sanitary appliance and their operation, building drainage system
of plumbing.
CE 604 – Geo Tech Engg. I
Unit - I
Basic Definitions & Index Properties : Definition and scope of soil
mechanics, Historical development. Formation of soils. Soil
composition. Minerals, Influence of clay minerals on engineering
behaviour. Soil structure. Three phase system. Index properties and
their determination. Consistency limits. Classification systems based on
particle size and consistency limits.
Unit - II Soil
Water and Consolidation : Soil water, Permaeability Determination of
permeability in laboratory and in field. Seepage and seepage pressure.
Flownets, uses of a flownet, Effective, neutral and total stresses.
Compressibility and consolidation, Relationship between pressure and
void ratio, Theory of one dimensional consolidation. Consolidation test,
Fitting Time curves. Normally and over consolidated clays.
Determination of preconsolidation pressure, settlement analysis.
Calculation of total settlement.
Unit - III
Stress Distribution in Soils and Shear Strength of Soils: Stress
distribution beneath loaded areas by Boussinesq and water gaurd’s
analysis. Newmark’s influence chart. Contact pressure distribution.
Mohr - Coulomb’s theory of shear failure of soils, Mohr’s stress
circle, Measurement of shear strength, Shear box test, Triaxial
compression test, unconfined compression test, Value shear test,
Measurement of pore pressure, pore pressure parameters, critical void
ratio, Liquefaction.
Unit - IV Stability of
Slopes: Infinite and finite slopes. Types of slope failures, Rotational
slips. Stability number. Effect of ground water. Selection of shear
strength parameters in slope stability analysis. Analytical and
graphical methods of stability analysis. Stability of Earth dams.
Unit - V
Lateral Earth Pressure: Active, passive and earth pressure at rest.
Rankine, Coulomb, Terzaghi and Culmann’s theories. Analytical and
graphical methods of determination of earth pressures on cosion-less and
cohesive soils. Effect of surcharge, water table and wallfriction.
Arching in soils. Reinforced earth retaining walls.
CE 605 – Structural Design & Drawing – II (Steel)
Unit - I Various
loads and mechanism of the load transfer, partial load factors,
structural properties of steel, Design of structural connections
-Bolted, Rivetted and Welded connections.
Unit - II Design of compression members, Tension members, Roof Trusses - Angular & Tubular, Lattice Girders.
Unit-III Design of simple beams, Built-up beams, Plate girders and gantry girders.
Unit - IV
Effective length of columns, Design of columns-simple and compound,
Lacings & battens. Design of footings for steel structures, Grillage
foundation.
Unit - V Design of Industrial building frames, multistory frames, Bracings for high rise structures, Design of transmission towers.
NOTE: - All the designs for strength and serviceability should strictly be as per the latest version of IS:800.
Check out RGPV B.E 6th Semester (Grading System) Syllabus.
